107/05 ID# M671111© COPYRIGHT 2005 by HUFFY SPORTSToll-Free Customer Service Number for U.S: 1-800-558-5234,For Canada: 1-800-284-8339,For Europe:
10ID# M671111 07/05TOOLS REQUIRED FOR THIS SECTIONSECTION A: ASSEMBLE THE BASE And/Or:This is what your system will look likewhen you’ve finis
07/05 ID# M671111111A.Check the following pre-assembled base areas for tightness: Eye bolts P/N203452, Washer P/N 203218, Nut P/N 203100, Carriage B
12ID# M671111 07/05Check the following pre-assembled handle areas for tightness: Screw P/N 204803,Nut P/N 203100, Carriage Bolts P/N 203103 .
07/05 ID# M671111136543.WOOD SCRAP(NOT SUPPLIED)54While maintaining alignment, bounce middle pole section (5) into top section (4)using a wood scrap
14ID# M671111 07/054.456WOOD SCRAP(NOTSUPPLIED)RODS SHOWN AREFOR VISUALREPRESENTATIONOF ALIGNMENTAND ARE NOTSUPPLIED WITHTHE HARDWARETROUGHTRO
07/05 ID# M6711111597697138455.Install bolt (12) through bracket and bottom polesection (6) and secure with nut (10) as shown. Nutshould be tightene
16ID# M671111 07/058.Install pole mount bracket (15) and reinforcement bracket (42) with carriage bolts(16) as shown. Tighten flange nuts (14
07/05 ID# M67111117Assemble lanyard (25) to locking pin (24) as shown (FIG A). Attach covers (22) ontopole mount bracket (15) with carriage bolt (23
18ID# M671111 07/05TOOLS REQUIRED FOR THIS SECTIONSECTION B: ATTACH THE BACKBOARD Phillips-HeadScrewdriverThis is what your system will look l
07/05 ID# M67111119Assemble backboard brackets (27) using bolts (43), and nuts (8) as shown.1.27438843
2ID# M671111 07/05BEFORE YOU START!To ensure optimal playability of backboard system, a close tolerance fit between the elevatorcomponents and
20ID# M671111 07/052.Attach lower elevator tubes (32) and counter balance springs (33) to backboardsupport brackets (27) using spacers (26), b
07/05 ID# M671111213.505214849Install Slam Jam Rim to Backboard345149152ABCDEA Fit rim (34) securely into bracket (48) as shown. Allow T-bolt (49)
22ID# M671111 07/054.Attach upper elevator tubes (35) to backboard support brackets (27) usingspacers (26 & 11), bolt (29), and nut (31) a
07/05 ID# M6711112331 31 40383243737293032302932293530313135303736365.Support pole on sawhorse. Attach backboard assembly to top pole section (4)as
24ID# M671111 07/058.Insert bolt (29) through left sideupper elevator tube (35), thenstretch spring (33) onto bolt (29).Insert bolt (29) throu
07/05 ID# M671111251. Apply height adjustment and moving label (46) to front of pole as shown.2.A.While holding handle, remove pin (24).B.Move eleva
07/05 ID# M6711113Owner must ensure that all players know and follow these rules for safe operation of the system.WARNING•DO NOT HANG on the rim or
4ID# M671111 07/05SAFETY INSTRUCTIONSFAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS MAY RESULT IN SERIOUS INJURY ORPROPERTY DAMAGE AND WILL VOID
07/05 ID# M6711115IMPORTANT!Remove all contents from boxes.Be sure to check inside pole sections;hardware and additional parts are packed inside.NOT
6ID# M671111 07/05Get to know the basic parts of your basketball system...FRONTPANELBACKBOARDFRONTRIMBASEPOLE
07/05 ID# M6711117PARTS LIST - (See Hardware Identifier)Item Qty. Part No. Description1 1 203470 Washer, Flat, 1.5” O.D.2 1 806620 Base Assembly3 1
8ID# M671111 07/05HARDWARE IDENTIFIER (BOLTS & SCREWS)* You may have extra parts with this model.#7 (2)#40 (1)#39 (2)Item #23 (1)#29 (6)#1
07/05 ID# M6711119HARDWARE IDENTIFIER (NUTS & WASHERS)HARDWARE IDENTIFIER (PLASTIC SPACERS CAPS & CLIPS)HARDWARE IDENTIFIER (OTHER)#13 (2)#2
Commentaires sur ces manuels