Huffy Universal Elevator Mount Manuel d'utilisateur télécharger pdf

10/01 P/N 211125A

Customer Service Center

N53 W24700 South Corporate Circle

Sussex, WI 53089

U.S.A.

A Huffy Company

Required Tools and

Materials:

NOTE: Due to various mounting

methods, additional tools and

materials may be required.

• Two People

• Tape Measure

• Pencil

• Wrenches: (Two) 7/16”, 1/2”,

9/16”, 3/4”

or Large and Small Adjustable

Wrenches

• Step Ladder 8 ft. (2.4 m)

• Drill & Bit (3/8”)

• Carpenter Level

Universal Elevator Mount Owners Manual

printed on recycled paper

Toll-Free Customer Service Number for U.S: 1-800-558-5234 and Canada Only: 1-800-284-8339

Internet Address: http://www.huffysports.com

WRITE IN YOUR MODEL NUMBER:

SAFETY INSTRUCTIONS

FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS MAY

RESULT IN SERIOUS INJURY,

PROPERTY DAMAGE AND WILL VOID WARRANTY.

Owner must ensure that all players know and follow these

rules for safe operation of the unit.

To ensure safety, do not attempt to assemble this system without

following the instructions carefully. Check entire box and inside all

packing material for parts. Before beginning assembly, read the

instructions and identify parts using the hardware identifier and parts

list in this document. Proper and complete assembly, use and

supervision are essential for proper operation and to reduce the risk of

accident or injury. A high probability of serious injury exists if this

system is not installed, maintained, and operated properly.

• This equipment is intended for home recreational use only and NOT

excessive competitive play.

• Read and understand the warning label enclosed with hardware. It is

the responsibility of the customer to mount this label. It should be

affixed to the pole, wall, or door near playing area, at a height between

4-6 feet (1.2 -1.8 m) above ground level and in a location visible to all

players.

• During assembly, if using a ladder use extreme caution. Two people are

recommended for this operation.

• If technical assistance is required, contact Huffy Sports.

• Adult supervision is recommended when adjusting height.

Most injuries are caused

by misuse and/or

not following instructions.

Use caution when using this unit.

IMPORTANT! Have questions...don’t go back to the store!

We appreciate your purchasing one of our many fine products. We are sure that you will be very satisfied with your selection. Although

great care and effort have been taken, occasionally problems may occur. To ensure prompt and correct handling of any problems, or to

answer any questions, please contact our Toll-Free Customer Service Number listed below.

Service will be quicker if you have your

Model Number (found on carton) and assembly instructions ready when calling. PLEASE WRITE YOUR MODEL NUMBER IN

THE SPACE PROVIDED ABOVE.

1 2 3 4 5 6 ... 10 11

Résumé du contenu

Page 1 - SAFETY INSTRUCTIONS

110/01 P/N 211125ACustomer Service CenterN53 W24700 South Corporate CircleSussex, WI 53089U.S.A.A Huffy CompanyRequired Tools and Materials:NOTE: Due

Page 2 - ADJUSTMENT

10P/N 211125A 10/013. NOTE: Two people required for thisprocedure, elevator assembly isheavy. Mount assembled elevatorcomponents to mounting bracket

Page 3 - ROOF MOUNTING

1110/01 P/N 211125AItem #5 (2)HARDWARE IDENTIFIERPARTS LIST * YOU MAY HAVE EXTRA PARTS WITH THIS MODEL.Item #4 (2)Item Qty. Part No. Description11206

Page 4

2P/N 211125A 10/01 WARNINGFAILURE TO FOLLOW THESE WARNINGS MAY RESULTIN SERIOUS INJURY AND/OR PROPERTY DAMAGE.Owner must ensure that all players k

Page 5

310/01 P/N 211125AIMPORTANT! WRITE DOWN MODEL NUMBER FROM BOX ON PAGE 1 OF THIS OWNERS MANUAL1. ROOF MOUNTING2. 34Secure struts (3) to upper holes o

Page 6 - Backboard

4P/N 211125A 10/01Drill holes in roof. Position angled brackets andsecure to roof. NOTE: Hardware for thisprocedure not included due to various roo

Page 7 - IMPORTANT!

510/01 P/N 211125A1911211722192010IMPORTANT! Test fit bolts into holes of brackets (8) and carefully rockthem in a circular motion to ream out paint f

Page 8 - FOR POLE MOUNTING ONLY

6P/N 211125A 10/01Assemble elevator tubes (17) to backboard bracket (8).22191817Backboard and RimNOTIncluded81713. Starting with nuts flush against br

Page 9 - FLAT SURFACE MOUNTING

710/01 P/N 211125A14. NOTE: Two people are required for this procedure, use caution, elevator assembly is heavy.Attach backboard and elevator assembly

Page 10 - IS 10 FEET (3.05 m)

8P/N 211125A 10/01FOR POLE MOUNTING ONLY1. Assemble mounting brackets (24) to 3-1/2” (8.9 cm) pole as shown.Position bracket assembly to approx. 106”

Page 11 - PARTS LIST

910/01 P/N 211125AFLAT SURFACE MOUNTING 1. A solid mounting base and/or surface,capable of withstanding normalrecreational use forces, must beprovided